Are you looking for this Classic Solid Door Aluminum Pull Handles? This door pull handle is made of high quality material which can be used for long time in daily life. This pull door handle is perfectly designed for you shoe cabinet, bookcase, drawer, and wardrobe and so on. Featured the appropriate size, this cabinet pull handle is quite easy for you to install. And the solid pull handle design of this door pull handle can match your doors or cabinets perfectly. Moreover, this door pull handle, with the simple and practical design, is comfortable to hold. Choosing it is your very choice.
## Product Description
Solid pull handle can match your doors perfectly
High quality madedoor pull handle is perfect for a long time use
This pull handle can help you create a stylish and complete look
Thisdoor pull handle is comfortable for you to hold
This pull handle is perfect for you shoe cabinet, bookcase, drawer,wardrobe and so on
Size:110 x 16mm/4.3 x 0.6in(L x W)
Screw Hole Distance: 96mm/3.8in
This door pull handle is made of high quality material which can be used for long time in daily life
This pull door handle is perfectly designed for you shoe cabinet, bookcase, drawer, and wardrobe and so on
Featured the appropriate size, this cabinet pull handle is quite easy for you to install
And the solid pull handle design of this door pull handle can match your doors or cabinets perfectly
Moreover, this door pull handle, with the simple and practical design, is comfortable to hold
How to Remove a Door Handle
Print this article Removing a door handle is a fairly simple process that can be done in just a few minutes. A door handle is fastened to the door with just a few screws; once they are removed, the handle assembly freely slides out.
Locate the screws that are holding the door handle onto the door. They are normally found on the interior side of the door, on the plate behind the door handle.
Unfasten the screws on the plate with a screwdriver until they are dislodged from the other door handle. Slide the door handle with the screws away from the door.
Remove the door handle on the opposite side of the door. Pull it straight out from the door jamb latch that runs through the hole in the door.
Unfasten the door jamb latch from the side of the door. Use a screwdriver to undo the screws and pull the door jamb latch out of the socket.
Undo the strike plate on the door jamb by removing the screws with a screwdriver.
Tips & Warnings
If the door jamb latch sticks, or is difficult to remove, slide a screwdriver through the back of the latch inside the door handle keyhole and tap the screwdriver with a hammer to loosen the latch.
How to Install Door Handles
Print this article Door handles are available in many varieties to suit the needs of different applications. Some handles are designed as non-latching pulls, while others use levers or knobs with built-in latches. Most door handles are easy to install and require only basic tools. The average DIY homeowner can install a door handle in less than an hour, depending on the complexity of the hardware and the type of door in use.
Use pull handles for operating doors that do not need latches. These handles are commonly found on closets and kitchen doors. They are surface-mounted, using screws or bolts.
Determine whether the handle is designed to be fastened through the door or just on the surface. If you see visible screw holes on the plate around the handle, the unit is surface-mounted. If there are no screw holes, the handle is meant to be fastened through the back of the door.
Decide where you will install the handle and mark the locations for screw holes. Pre-drill these holes using a bit that is one size smaller than the screws or fasteners. Hold surface-mounted handles on the face of the door and insert screws through any screw holes you see. For through-bolted handles, insert the connecting rods through the pre-drilled holes and hold the handle flush to the door. From the other side of the door, screw the included washers or plugs to the connecting rods.
Levers and Knobs
Use levers and knobs when you want a door to stayed latched or locked. If you simply want the door to stay closed, but do not want it to lock, select a passage set. If you want the door to lock, choose handles with built-in cylinders.
Open the lock package and remove the paper template from inside. Tape or stick this template to the door at the location indicated on the manufacturer's installation instructions.
Drill holes for the handle as indicated on the template. Use a hole saw on wood doors, or a bi-metal hole saw on metal doors. Pre-drill any screw holes that are shown on the template as well. Be sure to create these holes on both the surface and edge of the door as needed.
Place the interior side of the handle set into the hole you drilled in Step 3. Align the connecting rods and spindle with the appropriate openings on the exterior side of the lockset. Press the two sides together until they are tight to the door. Install set screws on the interior side of the handle as indicated on the template or instructions.
Use the template to determine the location of the strike on the door frame. Use a hole saw to create a hole for the latch. Chisel out a pocket for the strike plate. Screw the strike plate in place, using the included fasteners. Test the door to confirm it is operational. Remove the templates to complete the project.
* 1 x Pull Handle